/
/
Hydraulic Fluid

Hydraulic Fluid

This article will provide guidance on maintaining hydraulic fluid cleanliness. The charts in this article show several scenarios ranked by severity. Each level is determined by examining the PPM levels detected through the fluid analysis findings. These are a few examples of fluid contamination or mechanical failure scenarios. General knowledge of all components on the machine is required.

Snorkel products may operate on different fluid viscosities depending on what region the machine is operated in. Not all hydraulic fluid is suitable for use in our hydraulic system. Some have poor lubricating characteristics and may increase component wear. Only use hydraulic fluid that is recommended for your regional climate. It is recommended to keep hydraulic fluid within 100°F (38°C) of the ambient temperature where the machine is being operated.

While there is no single ISO rating that is best for all aerial lifts, all Snorkel lifts are typically delivered with ISO 32 hydraulic fluid as standard for its ability to operate in a majority of climates in temperatures as low as 0° F (-17° C). Reference the chart below to help determine the correct fluid necessary for your regional climate. For special applications, it is best to contact the Snorkel Service Department for guidance at 1-800-255-0317.
 

hydraulic fluid chart

It is recommended that with all fluid contamination and/or mechanical failures, a fluid sample should be taken and sent in for analysis. (Refer to: TCB 22.017 for more information on fluid sampling.) A few situations that could be contributing factors to contamination may be;

  • High loads, pressures or speeds
  • High temperatures
  • Low temperatures
  • Wet environment

Below is a chart representing potential contamination or component failure and some recommended actions. The list below is only a sample and should not be considered a comprehensive list.

HYDRAULIC FLUID CONTAMINATION RECOMMENDED ACTIONS

Contamination Priority
Level

Potential Contamination
Cause Or Component Failure

Recommended Actions

 

Normal (Level 1 Action)

 

  1. Normal wear

 

  1. Proceed with standard preventive maintenance practices

 

 

Abnormal (Level 2 Action)

 

  1. Valve failure/damaged within valve body (Spool, Counter- Balance Valve, Check Valve, Holding Valve)
  2. Water Contamination
  3. Incorrect Fluid

 

  1. Repair the failure
  2. Flush hydraulic system if needed
  3. Replace hydraulic filter
  4. Proceed with standard preventive maintenance practices
  5. Use the fluid sample kit as needed

 

 

Severe (Level 3 Action)

 

 

  1. Hydraulic Pump/Drive Motor failure
  1. Repair the failure
  2. Flush hydraulic system
  3. Replace hydraulic filter
  4. After every 50 hours of operation, cut hydraulic filter open to check severity, if needed repeat the top actions
  5. Proceed with standard preventive maintenance practices
  6. Use the fluid sample kit as needed
 

Normal – Equipment, contamination and fluid conditions are within an acceptable range. No other steps are required. 

Abnormal – Conditions are present that may require monitoring or diagnosis to minimize impact on equipment and lubricant performance. Refer to level 1 & 2 action for possible corrective actions.

Severe – Conditions exist that exceed acceptable limits or require corrective action. Steps should be taken to confirm and correct the condition. Refer to level 3 action for possible corrective actions.

This video and content posted in this section are provided for informational purposes only. To the fullest extent permitted by law, we will not be liable for any damages, including but not limited to, injury, loss, damage, cost or expense incurred in relation to or arising by reason of any person relying on the information from any video or posts in this section. While reasonable care is take in relation to these videos and posts, we do not guarantee or warrant the accuracy, reliability, completeness or currency of the information on these videos and posts. For further specifics and instructions, please refer to the operator manual of each respective piece of equipment.

The Toolbox™ Sign Up

Get expert advice on equipment service and safety, parts, care and maintenance, and more. Subscribe to The Toolbox™ for emailed updates.

Keep it simple with a single subscription to receive all Snorkel company news, events and product updates – direct to your inbox!


By submitting this form, you are consenting to receive marketing emails from: . You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact
the-platfoem

ONLINE PARTS ORDERING & TECHNICAL PUBLICATIONS